In high-temperature applications such as vacuum furnaces and atmosphere furnaces, graphite component selection is often simplified to “looking at density, strength, and ash content.” But what truly determines whether a material can be used stably over the long term is not just these numbers—it is the mandatory inspection items behind the executive standard. Even if two graphite materials have almost identical density, flexural strength, and ash content, as long as they follow different standards and have different mandatory inspection items, they cannot be interchanged at will.
This guide integrates selection standards, indicator comparisons, judgment logic, and common pitfalls for isostatic graphite in vacuum furnace scenarios, machined artificial graphite crucibles, and EDM graphite electrodes. It can be used as a technical specification or selection reference.
Part I. Vacuum Furnace Graphite Selection
I-1. Core Principle: Define the Scenario First, Then Match the Standard
This series of isostatic graphite products can be divided by working conditions into: photovoltaic hot zone, vacuum sintering furnace, vacuum heat treatment furnace, rare metal melting, casting mold, and nuclear-grade components.
Different application scenarios correspond to different national/industry standards. In addition to conventional physical and chemical indicators (density, strength, resistivity, ash content, etc.), some scenarios have additional mandatory inspection items (isotropy, irradiation performance, etc.). Similar physical and chemical values alone cannot determine material equivalence; the complete standard and mandatory inspection items must be matched.
Each product entry should have three fixed blocks of information: [Applicable Working Conditions] → [Executive Standard] → [Physical and Chemical Indicators + Special Constraints], plus [Selection Notes / Prohibited Scenarios], so that customers and technical personnel can see at a glance whether it can be used.
I-2. Vacuum Furnace Scenario – Standard – Indicator Comparison Table
| Vacuum Furnace Sub-Scenario | Recommended Executive Standard | Recommended Grades | Core Mandatory Inspection Items | Indicator Focus & Trade-off Notes |
|---|---|---|---|---|
| Single-crystal silicon growth vacuum hot zone (photovoltaic) | YB/T 6267-2024 | DJY-G1/G2/G3 | Bulk density, flexural strength, resistivity, thermal expansion, isotropy, ash content, apparent porosity | Mandatory isotropy; extremely low ash content to prevent silicon material contamination; thermal shock stability takes priority; cannot be replaced by YB/T 4379 even if physical and chemical values are similar, as the general standard has no mandatory isotropy requirement |
| Cemented carbide / ceramics / powder metallurgy vacuum sintering furnace | YB/T 4379-2014 | DJY40~DJY60 | Bulk density, flexural strength, resistivity, thermal expansion, ash content, apparent porosity | High density, high strength, low porosity; moderate ash content requirement; isotropy is a supplier-buyer negotiated item, not mandatory; lower cost than photovoltaic grade |
| Metal vacuum annealing / vacuum quenching heat treatment furnace | YB/T 4379-2014 | DJY10~DJY30 | Bulk density, flexural strength, thermal expansion, apparent porosity | Relaxed requirements for ash content and isotropy; focus on thermal shock resistance; lower grades can be selected to reduce cost |
| Rare metal vacuum melting crucible (titanium / precious metals) | YB/T 4379-2014 (additional supplementary clauses in technical agreement) | DJY50/DJY60 | Basic physical and chemical properties + additional high-purity, low-impurity, and isotropy requirements added in the agreement | The basic standard uses general isostatic graphite, with additional constraints separately added in the technical agreement; the photovoltaic national standard is not directly applied |
| High-temperature gas-cooled reactor vacuum in-core components | GB/T 40408-2021 | IIG/ING | Ash content, isotropy, thermal conductivity, tensile strength, irradiation performance | Nuclear-grade exclusive; irradiation assessment is the core; extremely high cost; completely unnecessary for ordinary vacuum furnaces |
| Casting mold (non-vacuum, for reference) | YB/T 4746-2019 | DJY-Z series | Compressive strength, flexural strength, thermal expansion, ash content | Focus on compressive strength; high ash tolerance; not suitable for high-purity vacuum conditions |
I-3. Main Product Specifications and Indicators
Product 1: Isostatic Graphite for Photovoltaic Hot Zones
-
Applicable Working Conditions: Single-crystal silicon growth vacuum hot zone (crucibles, insulation cylinders, support parts), high-temperature argon/vacuum environment, workpieces extremely sensitive to impurities, large-sized components undergoing severe thermal cycling.
-
Executive Standard: YB/T 6267-2024 “Isostatic Graphite for Photovoltaic Hot Zones”
-
Available Grades: DJY-G1, DJY-G2, DJY-G3
| Item | Unit | DJY-G1 | DJY-G2 | DJY-G3 |
|---|---|---|---|---|
| Bulk Density ≥ | g/cm³ | 1.82 | 1.84 | 1.85 |
| Flexural Strength ≥ | MPa | 45 | 50 | 55 |
| Resistivity ≤ | μΩ·m | 12 | 10 | 9 |
| CTE (RT–600°C) ≤ | 10⁻⁶/°C | 3.5 | 3.0 | 2.6 |
| Ash Content ≤ | % | 0.05 | 0.03 | 0.01 |
| Apparent Porosity ≤ | % | 11 | 10 | 8 |
| Isotropy | — | ≤1.12 | ≤1.10 | ≤1.08 |
Technical Notes: Isotropy is a mandatory factory inspection item; extremely low ash content prevents silicon material contamination; not recommended for ordinary heat treatment vacuum furnaces (cost too high); cannot be replaced by YB/T 4379 series graphite.
Product 2: Isostatic Graphite for Powder Metallurgy / Cemented Carbide Vacuum Sintering Furnaces
-
Applicable Working Conditions: Vacuum sintering furnaces for cemented carbide, ceramics, and powder metallurgy products; vacuum/protective atmosphere high-temperature sintering; certain requirements for impurities; large-sized components carry thermal shock risk.
-
Executive Standard: YB/T 4379-2014 “Isostatic Graphite”; additional clauses can be added in the technical agreement.
-
Available Grades: DJY40, DJY50, DJY60
| Grade | Bulk Density ≥ g/cm³ | Flexural Strength ≥ MPa | Resistivity ≤ μΩ·m | CTE (RT–600°C) ≤ 10⁻⁶/°C | Ash Content ≤ % | Apparent Porosity ≤ % |
|---|---|---|---|---|---|---|
| DJY40 | 1.82 | 45 | 11 | 3.5 | 0.05 | 11 |
| DJY50 | 1.84 | 50 | 10 | 3.0 | 0.02 | 10 |
| DJY60 | 1.85 | 60 | 8 | 2.0 | 0.01 | 8 |
Technical Notes: The standard itself does not mandate isotropy. If components are large and thermal cycling is severe, an additional constraint can be added in the technical agreement: isotropy ≤1.08; ash content and purity meet high-purity sintering requirements; cost is lower than photovoltaic-grade graphite.
Product 3: Isostatic Graphite for Metal Vacuum Heat Treatment Furnaces (Annealing/Quenching)
-
Applicable Working Conditions: Vacuum annealing and vacuum quenching of steel, 800–1200°C vacuum environment, low workpiece sensitivity to impurities, small and medium-sized graphite parts.
-
Executive Standard: YB/T 4379-2014 “Isostatic Graphite”
-
Available Grades: DJY10, DJY20, DJY30
| Grade | Bulk Density ≥ g/cm³ | Flexural Strength ≥ MPa | Resistivity ≤ μΩ·m | CTE (RT–600°C) ≤ 10⁻⁶/°C | Ash Content ≤ % | Apparent Porosity ≤ % |
|---|---|---|---|---|---|---|
| DJY10 | 1.70 | 30 | 15 | 4.5 | 0.20 | 15 |
| DJY20 | 1.75 | 35 | 14 | 4.2 | 0.15 | 14 |
| DJY30 | 1.80 | 40 | 12 | 3.8 | 0.10 | 12 |
Technical Notes: No strict requirements for ash content or isotropy; priority is thermal shock resistance and strength; high cost performance, suitable for ordinary heat treatment vacuum furnaces.
Product 4: Graphite for Rare Metal Vacuum Melting Crucibles
-
Applicable Working Conditions: Vacuum melting crucibles for titanium and precious metals, vacuum high temperature, workpieces sensitive to impurities, isotropy controlled on demand.
-
Executive Standard: YB/T 4379-2014 “Isostatic Graphite” + additional clauses in technical agreement
-
Available Grades: DJY50, DJY60
-
Additional Agreement Requirements: Ash content upper limit, isotropy, and impurity element content can be specified as needed.
-
Technical Notes: The basic standard uses general isostatic graphite. Additional requirements such as high purity and isotropy are specified through contract technical clauses, not directly applying the photovoltaic standard.
Product 5: Isostatic Graphite for Casting Molds
-
Applicable Working Conditions: Metal die casting and casting molds (non-vacuum conditions)
-
Executive Standard: YB/T 4746-2019 “Isostatic Graphite for Casting Molds”
-
Available Grades: DJY-Z10, DJY-Z20, DJY-Z30
| Item | Unit | DJY-Z10 | DJY-Z20 | DJY-Z30 |
|---|---|---|---|---|
| Bulk Density ≥ | g/cm³ | 1.72 | 1.78 | 1.83 |
| Flexural Strength ≥ | MPa | 32 | 38 | 46 |
| Compressive Strength ≥ | MPa | 65 | 75 | 90 |
| Resistivity ≤ | μΩ·m | 14 | 13 | 11 |
| CTE (RT–600°C) ≤ | 10⁻⁶/°C | 4.4 | 4.0 | 3.4 |
| Ash Content ≤ | % | 0.20 | 0.12 | 0.06 |
| Apparent Porosity ≤ | % | 14 | 13 | 10 |
Technical Notes: Focus on compressive strength; relatively high ash content; not recommended for high-purity vacuum furnaces or photovoltaic hot zones.
Product 6: Isostatic Graphite for Nuclear-Grade High-Temperature Gas-Cooled Reactors
-
Applicable Working Conditions: In-core reflector components of high-temperature gas-cooled reactors
-
Executive Standard: GB/T 40408-2021
-
Available Classifications: IIG Isotropic, ING Near-Isotropic
| Item | Unit | IIG Isotropic | ING Near-Isotropic |
|---|---|---|---|
| Degree of Isotropy | — | 1.00 ≤ α < 1.10 | 1.10 ≤ α < 1.15 |
| Bulk Density | g/cm³ | 1.75–1.85 | 1.75–1.85 |
| Thermal Conductivity (RT) ≥ | W/(m·K) | 120 | 110 |
| CTE (RT–500°C) | 10⁻⁶/°C | 3.5–5.5 | 3.5–5.5 |
| Tensile Strength ≥ | MPa | 24 | 20 |
| Compressive Strength ≥ | MPa | 70 | 65 |
| Ash Content | % | ≤0.005 | ≤0.008 |
Technical Notes: Irradiation performance must be assessed; used only for nuclear reactors; not required for ordinary vacuum furnaces.
I-4. Core Judgment Logic (to Be Written into the Technical Agreement)
-
Step 1: Determine whether the workpiece is sensitive to impurities
-
Melting silicon, high-purity ceramics, rare metals → strictly control ash content, prioritize high-purity systems;
-
Ordinary steel heat treatment → ash content requirements can be relaxed.
-
-
Step 2: Consider component size and thermal cycling amplitude
-
Large-sized components, repeated rapid heating and cooling → isotropy must be assessed; prioritize photovoltaic standards or add isotropy clauses to the general standard;
-
Small graphite parts, gentle temperature changes → isotropy may not be mandatory.
-
-
Step 3: Confirm outgassing risk under vacuum conditions
-
High vacuum with long-term heat preservation → low apparent porosity is required to reduce the slow release of gas adsorbed in pores and prevent vacuum degradation.
-
I-5. Common Pitfalls
Phenomenon: YB/T 4379 DJY60 has a density of 1.85 and ash content of 0.01%, almost the same as YB/T 6267 DJY-G3.
Essential Difference: YB/T 4379 has no mandatory isotropy requirement in its standard clauses.
Risk: The DJY60 supplied may have large differences in thermal expansion in different directions; large-sized vacuum furnace components may crack after thermal cycling. The photovoltaic standard lists isotropy as a mandatory factory inspection item.
I-6. Two Standard Wording Options for Technical Agreements
Option A (use photovoltaic standard):
The material shall comply with YB/T 6267-2024, grade DJY-G3, and all indicators shall meet all mandatory items of the standard.
Option B (general standard + additional constraints, cost-saving):
The material shall comply with YB/T 4379-2014, grade DJY60, with an additional supplementary clause in the technical agreement: isotropy ≤1.08. All indicators shall be accepted including the supplementary clause.
Option B is suitable for large-sized powder metallurgy vacuum sintering furnaces. It adds photovoltaic-grade isotropy requirements on the basis of general isostatic graphite, without purchasing a full set of photovoltaic hot zone special material.
I-7. Selection Judgment Rules (Technical Tips)
-
First confirm the operating environment: whether vacuum/protective atmosphere, working temperature, and thermal cycling amplitude;
-
Confirm the workpiece being processed: whether it is sensitive to impurities (silicon, high-purity ceramics, rare metals require strict ash control);
-
Confirm component size: large size + severe thermal shock requires isotropy assessment;
-
Material acceptance: all mandatory items of the selected standard must be fully implemented; do not compare only individual physical and chemical indicators;
-
Testing method: Ash content chemical analysis shall uniformly adopt GB/T 3521-2023 “Methods for Chemical Analysis of Graphite.”
Part II. Machined Artificial Graphite Crucible Material Selection
Machined artificial graphite crucibles operate under severe thermal cycling, molten metal wetting and erosion, and continuous high-temperature static loads. The furnace atmosphere directly determines the actual service life of the crucible. Therefore, material selection should focus on carbon content, bulk density, apparent porosity, compressive strength, thermal shock resistance, appearance quality, and dimensional tolerances.
| Test Item | Class I (Copper, Precious Metals, Rare Earth Alloys) Isostatic Grade | Class II (Aluminum, Low-Melting-Point Metals) Isostatic Grade | Test Method |
|---|---|---|---|
| Carbon Content, % | ≥45 | ≥45 | GB/T 16555 |
| Bulk Density, g/cm³ | ≥1.85 | ≥1.85 | GB/T 2997 |
| Apparent Porosity, % | ≤21 | ≤21 | GB/T 2997 |
| Compressive Strength at Room Temperature, MPa | ≥25 | ≥25 | GB/T 5072.2 |
| Thermal Shock Resistance | 850°C water quenching cycle, no through cracks | 850°C water quenching cycle, no through cracks | Finished product test |
| Appearance Quality | No penetrating cracks, no hard slag protrusions on inner wall | No penetrating cracks, no hard slag protrusions on inner wall | Visual inspection |
| Dimensional Tolerance | Top outer diameter, height, bottom diameter ±2%; wall thickness per drawing | Top outer diameter, height, bottom diameter ±2%; wall thickness per drawing | Caliper measurement |
Selection Notes:
-
Class I: Suitable for high-temperature, demanding melting conditions such as copper, precious metals, and rare earth alloys. Focus on thermal shock resistance, melt erosion resistance, and high-temperature strength.
-
Class II: Suitable for aluminum and low-melting-point metals. The indicator requirements are the same as Class I, but can be adjusted according to actual temperature, corrosion, and cost.
-
Isostatic Grade: Uniform structure, good isotropy, and stable thermal shock resistance, suitable for machined artificial graphite crucibles.
-
Actual selection should also consider furnace atmosphere (oxidizing/reducing/vacuum), melt properties, heating/cooling rate, crucible size, and service life.
Part III. EDM Graphite Electrode Material Selection
EDM graphite electrodes are subjected to high-frequency pulses, instantaneous high temperatures, arc impact, and clamping stress during electrical discharge machining. Material selection should focus on bulk density, apparent porosity, flexural strength, Shore hardness, coefficient of thermal expansion, and ash content. Fine grain is suitable for precision EDM, mirror finishing, and micro structures; medium grain is suitable for general EDM rough machining and large stock removal.
| Test Item | Unit | Fine Grain (Precision EDM) | Medium Grain (General EDM Roughing) | Test Method |
|---|---|---|---|---|
| Bulk Density | g/cm³ | ≥1.78 | ≥1.72 | GB/T 2997 |
| Apparent Porosity | % | ≤16 | ≤19 | GB/T 2997 |
| Flexural Strength | MPa | ≥32 | ≥22 | GB/T 3074.1 |
| Shore Hardness | HSD | 45–65 | 35–55 | GB/T 39535 |
| Coefficient of Thermal Expansion | 10⁻⁶/℃ | ≤4.5 | ≤5.5 | GB/T 3074.2 |
| Ash Content | % | ≤0.10 | ≤0.15 | GB/T 14265 |
Selection Notes:
-
Fine Grain (Precision EDM): High bulk density, low porosity, high flexural strength, low thermal expansion, and low ash content. Suitable for precision molds, mirror EDM, micro ribs, sharp corners, and thin-wall structures.
-
Medium Grain (General EDM Roughing): Cost-effective. Suitable for mold roughing, large stock removal, and general cavity machining where surface finish and dimensional accuracy requirements are relatively lower.
-
For higher precision, lower electrode wear, or better surface quality, ultra-fine grain or isostatic high-purity graphite can be selected, with a separate technical agreement.
-
The above are typical reference indicators. Actual selection should consider machine performance, machining current, chip removal conditions, surface roughness requirements, and cost budget, and shall be subject to inspection reports and technical agreements.
Conclusion
Graphite selection for vacuum furnaces, crucibles, and EDM electrodes is not simply about “comparing numbers.” Working conditions determine the standard; the standard determines the inspection items. Only by combining the application scenario, executive standard, mandatory inspection items, and actual component size can you select truly reliable graphite materials without pitfalls. We hope this compilation helps you make more accurate judgments in technical agreements and procurement selection.
